Products

When pump rotors operate in abrasive, corrosive, or poorly lubricated media, the 20% glass PTFE bushing for pump applications provides a maintenance-friendly wear surface with low friction and strong dimensional stability. This bushing is produced from virgin PTFE compounded with 20% glass fiber to resist deformation under load and reduce thermal expansion. It is widely applied as a glass fiber filled PTFE sleeve bearing in centrifugal, gear, and submersible pump shafts. The PTFE bushing with fiberglass reinforcement structure improves creep resistance and load-carrying ability compared with unfilled PTFE, allowing the bushing to support radial and axial loads in both horizontal and vertical pump configurations. A qualified 20% glass PTFE bushing manufacturer controls the glass fiber dispersion and machining tolerances so that the final part fits existing pump housings without rework. The wear resistant PTFE bushing glass fille formulation resists scoring and abrasion from suspended solids, making it suitable for chemical transfer, wastewater, and slurry pump service. Since PTFE requires no external lubrication, these bushings reduce maintenance and eliminate grease contamination in sensitive process lines.

The 20% Glass PTFE Bushing for Pump is machined from stress-relieved PTFE stock containing 20% glass fiber by weight. This glass-reinforced composite balances chemical inertness, low friction, and mechanical strength. The bushing is available in plain sleeve and flanged configurations, and can be supplied with spiral grooves, lubrication holes, chamfers, and anti-rotation features. It operates quietly, absorbs shock and vibration, and maintains its shape under fluctuating pump pressures. The low coefficient of friction helps prevent shaft seizure during dry starts or temporary loss of prime, while the glass fibers lower the thermal expansion rate and improve the load-bearing capacity of the PTFE matrix.

• Material composition: 80% virgin PTFE, 20% glass fiber by weight
• Color: off-white to light tan
• Density: 2.15–2.20 g/cm³
• Hardness: Shore D 60–65
• Tensile strength: 25–30 MPa
• Elongation at break: 200–250%
• Compressive strength: 30–40 MPa
• Coefficient of friction: 0.05–0.10 dry against steel
• Operating temperature range: -100°C to 260°C (-148°F to 500°F)
• Water absorption: less than 0.1%
• Chemical resistance: excellent in acids, alkalis, solvents, and oxidizing media
• Available bore range: 8 mm to 120 mm standard, custom up to 300 mm outer diameter

The 20% Glass PTFE Bushing for Pump is manufactured with tight dimensional controls. Inner diameters are held to H9 tolerance, outer diameters to r7 or custom fit, and lengths to ±0.10 mm. Roundness and concentricity are maintained within 0.05 mm to reduce vibration in high-speed pump shafts. For flanged bushings, flange perpendicularity is controlled within 0.05 mm. The glass fiber reinforcement limits cold flow, so running clearances remain stable at elevated temperatures. When installed, a radial press allowance of 0.05–0.10 mm per 25 mm of outer diameter is recommended for retention, and a shaft running clearance of 0.08–0.15 mm is typical depending on shaft diameter and operating speed.

This bushing works well in API 610, ANSI, and ISO pump series, as well as in sealless magnetically driven pumps where product purity and dry-run protection are required. It is used as a throttle bushing, shaft sleeve, wear ring, and bowl bearing in vertical turbine pumps. Standard configurations include cylindrical bore, flanged bore, and split designs for easy installation. Custom machining can add straight or spiral grooves for fluid circulation, radial feed holes for lubrication, and notches for anti-rotation pins. Each batch is inspected for surface finish, dimensional accuracy, and glass fiber distribution. Material certificates and first article inspection reports are available on request. The 20% Glass PTFE Bushing for Pump can be supplied in small prototype quantities or full production lots, with lot traceability from raw material to finished part.

For pump rebuilders, the 20% Glass PTFE Bushing for Pump is often selected as a direct replacement for carbon, bronze, or PEEK bushings in chemical process pumps. It tolerates misalignment better than rigid metal or ceramic bearings, and it does not gall stainless steel shafts. Because the material is USDA and FDA compliant in virgin form, the glass-filled version remains suitable for many food and beverage pumps where the glass content is acceptable. It is also compatible with water, steam condensate, light hydrocarbons, and many aggressive solvents up to the stated temperature limit. End users report reduced wear on shaft sleeves and quieter operation after switching from metal bushings to glass-filled PTFE components in high-cycle pump stations.